Trial fit of driver and engine

026
First fit for driver, pretty snug
027
Going to have to work on my expressions
DSC_0948
Engine offered up to engine bay and transmission
DSC_0949
Note spirit level to get the carburettor float chambers level
DSC_0950
Engine will run slightly lower and further back in the car than original to help with balance and weight distribution
DSC_0947
Steering column work
DSC_0951
Steering box and column dummied up
DSC_0952
Engine view
DSC_0953
Mating for enlarged sump with rebuilt engine
DSC_0954
Engine to transmission checked
DSC_0955
Gearbox cross member

 

February 2015

DSC_0860
Front valence, bumper and wing on for fitting, car had taken a knock so getting the angles right was a pain
DSC_0861
Dash mock up for Robbie Durant the electrician to work with
DSC_0862
Drivers view dash
DSC_0863
Navigator dash
DSC_0852
Controls the width of the car
DSC_0853
Front suspension dummy assembly, planning for three shock absorbers
DSC_0855
New discs for Geen
DSC_0854
Parts on the bench prepped for spraying

Checking wheel clearance using original 14″ Magnums

DSC_0856   DSC_0857   DSC_0858

Front turrets

DSC_0842  DSC_0843

DSC_0844  DSC_0845

Pedal box

DSC_0846   DSC_0847

DSC_0796
Mesh guard for radiator and to stiffen up the parallelagram of the front square section
DSC_0797
Triangular support carried over from original and battery trays left and right, we later deleted the second battery on the near side in favour of one big boy on the off side to save weight
DSC_0787
John don’t smoke the reefer, he smokes the pipe, pipe, pipe

The fabrication goes on and on

DSC_0798    DSC_0799

DSC_0786    DSC_0789

DSC_0782
Cyber men built into the project

DSC_0781

DSC_0783    DSC_0784

Works Visit June 2014

126 (2)
Steve on the gas welding, Autosportif’s more usual stock in trade Subaru in background
106
Engine bay with seam welding, strengthened inner wings and turrets
107
Cabin floor
DSC_0337
rear turret tops and bracket for fuel tank mount. Shows roll cage tie ins to good effect
053
Right way up
DSC_0340
Starting to look the part
DSC_0333
So much preperation, filing and inserting captive nuts

DSC_0334 101 102 103

125 (2)
Steve entitled to look tired

Autosportif works visit

003
Hero driver showing the delicacy of his touch on the steering
004
Inside boot floor
005
Seat trial fit in cabin
007
Great work on body floor
008
Thinking ahead: cut out for exhaust and captive nuts for mudflaps
010
Inner wings
011
A frightening team, Chris Partington project consultant, Steve Wilson fabrications, Howard Dent, owner of Autosportif (and PI Magnum’s moustache) holding bent push rod
012
Subaru seat in situ, small but effective
013
cabin viewed through rear window
014
Engine bores in pleasingly good and clean condition, can’t have done many miles, great news
015
Crankshaft, cam and inlet manifolds all found in great condition
016
crank webs looking substantial
DSC_0299
Chassis stamp
DSC_0300
Chassis plate

Engine prepped for dismantling in Autosportif’s Clean Room

DSC_0277
Engine mounting off side sump and oil filter, note smog gear on end of exhaust manifold
DSC_0276
Front pulley with water pump above. Big timing marks on block visibl
074
Starboard side of engine coil on top and bottom of carb showing
082
Front of engine showing water pump and hose to radiator
081
Front left of engine mechanical fuel pump and distributor
080
Engine mounting and exhaust manifold on left side, we retained the simple along and down exhaust manifold but lost the smog reduction devices
079
Top view from front
078
Original carburettor
077
Oil filler turret and lid visible on left